PCPartPicker

  • Log In
  • Register

Comments

Talon2014's Completed Build: The 4K Destroya

FurryJackman 3 Builds 1 point 1 day ago

Desktop looking sweet! You know what would make it better?

Rainmeter!

https://www.rainmeter.net/

derblexp's Completed Build: 2019 RGB Ryzen 5 2600 Gaming Rig [for friend]

derblexp's Completed Build: 2019 RGB Ryzen 5 2600 Gaming Rig [for friend]

FurryJackman 3 Builds 1 point 3 days ago

And remember, just because people like TechPowerUp, Joker Productions and Tech YES City actively promote and hint at them, doesn't make them any more legitimate. These sites in fact operate illegally, doing MANY consistent name changes before concrete legal action can be taken.

They are strictly forbidden on this site.

DualPC's Completed Build: Lian-Li PC-O11AIR FULL-Dual PC

FurryJackman 3 Builds 1 point 6 days ago

Not really when considering x264 at "slow" for Twitch. x264 already is extremely stressful and for 1080p FPS streamers, it's no faster than "medium" x264 preset or bust.

Osbrandon's Completed Build: First PC Build. Simple and elegant. :)

FurryJackman 3 Builds 2 points 6 days ago

No, the cover just above the drive cage, which is the only way to take the drive cage out. It's in the manual about how to remove the drive cage in the lower area.

DualPC's Completed Build: Lian-Li PC-O11AIR FULL-Dual PC

FurryJackman 3 Builds 1 point 8 days ago

Make a Threadripper/9700K Dual PC with a Avermedia 4K HDR capture card and 1660 Ti on the 2950X Threadripper system, and a RTX 2080 on the 9700K ITX system.

That would be the ultimate streaming dual system setup.

Osbrandon's Completed Build: First PC Build. Simple and elegant. :)

FurryJackman 3 Builds 1 point 8 days ago

You can take out the drive cage at the bottom of the Meshify since you only run a M.2 SSD, and put the intake fan there after you remove the drive cage cover on the PSU shroud and the drive cage itself. There's ultra-fine dust filters there on that fan position so you won't be losing any dust filtering.

You can also forgo the mesh filter for the top if all the remaining fans there are exhaust.

bre1979's Completed Build: Showtime

FurryJackman 3 Builds 1 point 10 days ago

Caselabs + Watercool is a combo made in heaven!

I smell a feature.

jgtzjr's Completed Build: node 202 build

FurryJackman 3 Builds 3 points 10 days ago

Considering the space constraint inside the Node 202, it's a smart decision to have non-K OC parts. +1

CGreene's Completed Build: Entry Level TR4 build

FurryJackman 3 Builds 1 point 10 days ago

I think you got a bit of a problem with all the fans exhausting creating a ton of negative pressure. Negative pressure sucks in dust from any crevice in the case. This is not beneficial to run.

Personally, I would flip the front fans to intake, and reposition the 2 fans on the side bracket down to the bottom fan bracket to give the GPU airflow as intake.

Osbrandon's Completed Build: First PC Build. Simple and elegant. :)

FurryJackman 3 Builds 1 point 10 days ago

There's no need for the LED intake fan on the top right. Your exhaust will be sucked back into the case from that fan and it's better to have as much intake in the front as possible with a Meshify C.

Onemervone's Completed Build: Maya/Cinema4D redshift & Octane workstation

FurryJackman 3 Builds 1 point 13 days ago

I'm more intrigued by the DVCPRO and BETACAM decks you have below your PC...

Have you tried Cinebench R20 yet?

Arcadiazero's Completed Build: To RGB or not to RGB, What would Gaben do?

FurryJackman 3 Builds 1 point 13 days ago

Did you replace the stock dust filters on the O11 Air? The stock ones restrict too much airflow. Replacing them with Silverstone Ultra Fine dust filters may be something to improve airflow.

gthompson0912's Completed Build: Daydream Nation

FurryJackman 3 Builds 2 points 17 days ago

Are you the elusive "Banksy?" Because this would totally be the PC that Banksy uses as their daily driver!

Extremely well done! Give this guy a feature, please!

l2pTink3r's Completed Build: The Corsair Crystal Build - I did a thing.

FurryJackman 3 Builds 1 point 17 days ago

It's also not using an Asetek pump but a CoolIT pump which I believe has a higher flow rate if I'm not mistaken.

masterbot's Completed Build: MITX Adventures, And How Cooling Is Important

FurryJackman 3 Builds 1 point 20 days ago

KDE is the only one that has worked with NVIDIA FreeSync so far for me. It has a composition switch (Shift+Alt+F12 to turn on and off composition) while other DEs bury that option somewhere or make it impossible to turn off composition at will. (Muffin from Cinnamon and Linux Mint always has composition on)

Lobsterareawesome's Completed Build: Overkill "office" PC for my parents

FurryJackman 3 Builds 1 point 20 days ago

If your dad has an inner geek, buy him an unRAID license. He'll soon know he can consolidate most of his stuff into a single machine!

Granddy's Completed Build: $350 X79/LGA 2011 build

FurryJackman 3 Builds 1 point 20 days ago

Ooh, got bit with that on a Gigabyte board only supporting Ivy Bridge-E and not Ivy Bridge-EP. Wasted $280 on that one, cost me $650 to replace the Ivy Bridge-EP Xeon with a 4960X.

Granddy's Completed Build: $350 X79/LGA 2011 build

FurryJackman 3 Builds 1 point 22 days ago

Anything above 1.4 will kill the chip in a year. The C2 revision Sandy Bridge-EP processors degrade FAST.

Lobsterareawesome's Completed Build: Overkill "office" PC for my parents

FurryJackman 3 Builds 1 point 22 days ago

I so wish I got the same stuff that you did to experiment with Linux GPU passthrough.

Speaking of that, you could run their Windows OS on a unRAID VM and do a Plex server at the same time on this thing!

Granddy's Completed Build: $350 X79/LGA 2011 build

FurryJackman 3 Builds 2 points 22 days ago

Be careful of VRM temperatures on the Huanan once you start unlocked multiplier overclocking. Also, it's not a X79 chipset but a Z77 chipset hacked to make work with X79.

Once you get the 1650, DON'T exceed 1.4V Vcore or your chip will only last for 11 months before dying (First hand experience with that here) also, VTT should be below 1.175 and VCCSA should be below 1.06V.

Pist0l's Completed Build: LEBBEUS - BOLDR Q2 BUILD

FurryJackman 3 Builds 1 point 22 days ago

Have you considered the Radeon VII for stuff like Solidworks and etc?

masterbot's Completed Build: MITX Adventures, And How Cooling Is Important

FurryJackman 3 Builds 1 point 23 days ago

Have you been able to update your Kernel and Mesa to enable FreeSync? It does require the most bleeding edge Kernel and Mesa, but your monitor with low framerate compensation should I believe deliver a smoother experience than if the Freesync range was lower, like many 4K Freesync monitors currently have issues with framerate range.

stevierods's Completed Build: Stevie's Gaming Rig

FurryJackman 3 Builds 2 points 24 days ago

Eyy, I have that same Rick proping up my GPU as well!

bladd12001's Completed Build: A steppingstone into PC gaming 2.0

FurryJackman 3 Builds 1 point 24 days ago

May want to place the wireless antenna outside the case as signals would be able to get to the antenna instead of being blocked by the chassis.

I have that same GPU BTW. Works great for Hackintosh. Also works with CUDA in Premiere CC and Davinci Resolve on OSX.

Have you tried how Ryzen fairs with Premiere CC?

kyrk84's Completed Build: CruzanFPV unRaid Server

FurryJackman 3 Builds 1 point 26 days ago

BIG no go on that one. The VIA controller fails once IOMMU is engaged, and the Fresco Logic controller has a serious reset bug.

Get a card using the uPD720202 from Renesas. Do not get a card using a PLX because that lumps together the IOMMU groups of the onboard chips. Get separate x1 cards and bifurcate rather than use PCI-E Muxing.

You will want to use direct lanes from the CPU as well, because going through the chipset on X470/B450 will require ACS anyways.

kyrk84's Completed Build: CruzanFPV unRaid Server

FurryJackman 3 Builds 1 point 26 days ago

Since you are doing unRAID, I would invest in a few USB 3.0 controllers. This one from Startech is great:

https://www.startech.com/Cards-Adapters/USB-3.0/Cards/2-port-PCI-Express-USB-3-Card~PEXUSB3S24

Just remember to do some ACS if you have multiple of the same card in the system.

fn230's Completed Build: Artemisia, the cheapo Ryzen server

FurryJackman 3 Builds 2 points 27 days ago

Wendell would be proud. You're using Htop!

Just be sure to configure the rest of your network to block hard coded DNS requests (like from Google devices and apps) so that your PiHole gets used for those devices.

Jidonsu's Completed Build: Silver Bullet

FurryJackman 3 Builds 1 point 29 days ago

I personally smell a feature. This machine managed to mix soft tubing and hard tubing so well!

Also, Watercool (the company) is awesome!

kronikel's Completed Build: Ice and Fire

FurryJackman 3 Builds 1 point 29 days ago

That slot is electrically x8, but physically x16. The concern is more for airflow though.

bradgnoyes's Completed Build: 590 Bottles of Beer

FurryJackman 3 Builds 1 point 1 month ago

The fan in the top middle exhausting outward might steal airflow away for the AIO. I understand why you might want to have an additional one for GPU exhaust, but it would help the airflow patterns in the case if you only had 2 intakes and the AIO exhausting. Making the AIO push-pull with that fan is what I would do.

Classicalfredo's Completed Build: First Build in 15 years

FurryJackman 3 Builds 2 points 1 month ago

Decent part choices, just needs more intake fans. Some HP-12s from Fractal would work in the front.

61Builder's Completed Build: My Black Panther

FurryJackman 3 Builds 1 point 1 month ago

No problem! You can get a Xeon E5-1680 V2 and do a slight overclock on it with this board and BIOS version F7. It's worth a shot if you were looking for an upgrade without switching motherboards. 1680 V2 is 8 cores, 16 threads.

FurryJackman's Completed Build: Your Xeon Journey Ends Here. (Flexible and Powerful Repaired)

FurryJackman submitter 3 Builds 1 point 1 month ago

Yup, x16 for both GPUs, x4 for the Decklink Mini Recorder 4K, x1 for the USB 3.0 controller, plus all the onboard devices, which work for VFIO (minus the VIA USB 3.0 controller, which I disable whenever I run VFIO/QEMU/KVM)

Compromise's Completed Build: Quiet White

FurryJackman 3 Builds 1 point 1 month ago

+9001 for use of a M.2 riser for the Vive Wireless Adapter. Another +9001 for doing this in an ITX case!

61Builder's Completed Build: My Black Panther

FurryJackman 3 Builds 2 points 1 month ago

If your X79-UP4 is revision 1.1, you can replace that 4960X with a E5-1660 V2 or E5-1680 V2 Xeon. (BTW, they're overclockable with unlocked multipliers)

If it's revision 1.0, 4960X is the best you can go.

Taniwha67's Completed Build: Taniwha - Threadripper Workstation

FurryJackman 3 Builds 1 point 1 month ago

Good choice for the capture card! You running Dual System for streaming?

DenOfLore's Completed Build: The Widow-maker: a Golden $5k iHack Pro

FurryJackman 3 Builds 1 point 3 months ago

How's the iGPU performance in Premiere? And does the iGPU acceleration work with the 9900K?

killerelite1213's Completed Build: Keeping X58 alive

FurryJackman 3 Builds 1 point 3 months ago

You also need to have UEFI bootable NVMe support, and X58 I believe still runs on BIOS.

Finding a old OCZ or Intel PCI-E SSD with bootable support might be better.

killerelite1213's Completed Build: Keeping X58 alive

FurryJackman 3 Builds 2 points 3 months ago

Right, via an external controller. Many boards back then had external SATA 3 controllers. Might not have as much throughput as a native controller so I'd still get a 860 EVO.

killerelite1213's Completed Build: Keeping X58 alive

FurryJackman 3 Builds 4 points 3 months ago

Well on your way to a good Tech YES loving!

Since this is X58, you don't need more than a 860 EVO since the SATA interface is only SATA 2, not SATA 3.

Nintendao's Completed Build: Nov'18 | Personal custom loop upgrade

FurryJackman 3 Builds 1 point 3 months ago

How's Vega in Linux? Has it gotten better since launch?

ctbybe01's Completed Build: 2018 Hackintosh Dorm Room Build

FurryJackman 3 Builds 1 point 3 months ago

How does this work with Premiere CC? Does it work with iGPU acceleration?

Also, in my experience, Premiere likes CUDA more for Mercury acceleration.

Also, you can NATIVELY render ProRes with this setup! Windows Premiere can never render native ProRes at proper broadcast QC passing quality.

aznsniper911's Completed Build: My Last Build As A Single Man V2

FurryJackman 3 Builds 4 points 3 months ago

Paul's Hardware should see this. Proper competition for Riptide!

jgo1000's Completed Build: Meshify CG Workstation

FurryJackman 3 Builds 1 point 3 months ago

Evidence of negative pressure is clear with the dust in the picture. Flip the AIO to intake instead of exhaust. It will help with dust.

Smith's Completed Build: Ubuntu Media PC

FurryJackman 3 Builds 2 points 3 months ago

Try Cinnamon Desktop Environment. You'll be glad you did. It's way more beginner friendly than KDE.

raul3820's Completed Build: GreenMonster

FurryJackman 3 Builds 2 points 3 months ago

You could try your hand at QEMU/KVM Linux GPU passthrough with that card as the host GPU if you are inclined to experiment with virtualization.

Soul_fly's Completed Build: Evolve x RTX blue themed

FurryJackman 3 Builds 2 points 3 months ago

You may need to flip your AIO radiator fans to be intake. You're completely in a negative pressure airflow situation right now which sucks in dust. All your fans are exhaust with no intakes.

Warcobra's Completed Build: Custom Overkill Desk PC

FurryJackman 3 Builds 4 points 3 months ago

This is art. This is ACTUALLY art.

I smell a feature.

b00tup318's Completed Build: Bring Me The Kryptonian

FurryJackman 3 Builds 1 point 4 months ago

Curious if you could run GPU Passthrough on your Arch system with one of those Quadros, and if you don't need the error code 43 workaround.

Page
1
·
·